Free Standard shipping on orders over £50 + VAT on orders placed before Midday.
CS712 Axalta Percotop 2K Slow Activator 1L
£20.99+ VAT
- Product Code: CS712-1L
- Brand: Axalta
- Availability: In Stock
CS712 Axalta Percotop 2K Slow Activator 1L
£20.99+ VAT
CS712 Axalta Percotop 2K Slow Activator 1L
CS711 Axalta Percotop Activator VHS Standard 5L..
From £106.82 + VAT
CS712 Axalta Percotop Activator VHS Slow 5L..
From £106.82 + VAT
Yes , 10-15 minutes of short waves for the thickness of 150-250 µm. Do not exceed 60°C. Wait about 10 minutes before starting the heater drying.
The primer can be applied using a spray gun with a nozzle size of 1.7–2.0 mm. Apply 2–3 coats, allowing appropriate flash-off time between layers. Ensure good ventilation and follow safety precautions during application.
Yes, it can be applied to bare steel and aluminum, provided the surface is properly matted and degreased. For optimal adhesion and corrosion resistance, ensure thorough surface preparation.
Under standard conditions (20°C), the primer typically cures in 20–30 minutes before it can be sanded. Drying time may vary depending on ambient temperature, humidity, and film thickness
The primer should be mixed in a 5:1 ratio with the dedicated hardener. For example, 5 parts primer to 1 part hardener by volume. Always follow the manufacturer’s guidelines for best results
Firstly measure out 2% of the supplied hardener onto a mixing board, fold the hardener into the filler until a uniform colour is achieved. Try to to introduce air to the mix as this will cause pinholes
Yes. The putty is formulated for exceptional ease of sanding, allowing for a smooth finish with minimal effort — even on large areas
Yes, it can be applied to bare steel and aluminum, provided the surface is properly matted and degreased. For optimal adhesion and corrosion resistance, ensure thorough surface preparation.
This product uses advanced lightweight glass beads that reduce overall density, making it ideal for large surface repairs without adding unnecessary weight to the vehicle.
Simple , pour the excess resin away into your solvent waste. This is rejection not separation. Do not mix it in as you will introduce air to the filler and increase your chances of pinholes
Firstly measure out 2% of the supplied hardener onto a mixing board, fold the hardener into the filler until a uniform colour is achieved. Try to to introduce air to the mix as this will cause pinholes
Yes. The putty is formulated for exceptional ease of sanding, allowing for a smooth finish with minimal effort — even on large areas
This product uses advanced lightweight glass beads that reduce overall density, making it ideal for large surface repairs without adding unnecessary weight to the vehicle.
The primer can be applied using a spray gun with a nozzle size of 1.7–2.0 mm. Apply 2–3 coats, allowing appropriate flash-off time between layers. Ensure good ventilation and follow safety precautions during application.
Visual check: Look for a uniform matte finish. Touch Test. Surface should feel dry and firm, not tacky
The primer should be mixed in a 5:1 ratio with the dedicated hardener. For example, 5 parts primer to 1 part hardener by volume. Always follow the manufacturer’s guidelines for best results
Under standard conditions (20°C), the primer typically cures in 20–30 minutes before it can be sanded. Drying time may vary depending on ambient temperature, humidity, and film thickness
Visual check: Look for a uniform matte finish. Touch Test. Surface should feel dry and firm, not tacky
The PPE needed to spray any 2K (2 pack) product including Epoxy is a good respirator, ideally air fed. safety glasses or goggles , gloves and overalls
No, mixing technologies will only cause problems. always activate your paint using the information found on the Technical data sheet with the correct hardener stated on the same Technical data sheet.
When working with any 2K products, it is recommended to use personal protection equipment such as Air Fed respirator, safety goggles and gloves to Protect the eyes and respiratory system.
The primer should be mixed in a 4:1 ratio – four parts primer to one part hardener. This ensures optimal curing time, adhesion, and surface finish
Simple , pour the excess resin away into your solvent waste. This is rejection not separation. Do not mix it in as you will introduce air to the filler and increase your chances of pinholes
Yes , 10-15 minutes of short waves for the thickness of 150-250 µm. Do not exceed 60°C. Wait about 10 minutes before starting the heater drying.
5-10 minutes between coats then 10 minutes before baking at 60°C
Yes, it adheres excellently to steel and aluminum, provided the surface is properly flatted and degreased. It also works well on zinc-coated steel, fiberglass, and previously painted surfaces in good condition.
The Indasa MTE Neon Masking Tape is the superior choice for automotive applications due to its exceptional adhesion, high-temperature resistance (up to 100ºC), UV protection, and waterproof performance. It’s specifically designed for demanding environments, ensuring clean, precise lines and reliable results, even in extreme conditions.
The PPE needed to spray any 2K (2 pack) product including Epoxy is a good respirator, ideally air fed. safety glasses or goggles , gloves and overalls
No, mixing technologies will only cause problems. always activate your paint using the information found on the Technical data sheet with the correct hardener stated on the same Technical data sheet.
The Indasa MTE Neon Masking Tape is the superior choice for automotive applications due to its exceptional adhesion, high-temperature resistance (up to 100ºC), UV protection, and waterproof performance. It’s specifically designed for demanding environments, ensuring clean, precise lines and reliable results, even in extreme conditions.
The Indasa MTE Neon Masking Tape is the superior choice for automotive applications due to its exceptional adhesion, high-temperature resistance (up to 100ºC), UV protection, and waterproof performance. It’s specifically designed for demanding environments, ensuring clean, precise lines and reliable results, even in extreme conditions.
Yes, it adheres excellently to steel and aluminum, provided the surface is properly flatted and degreased. It also works well on zinc-coated steel, fiberglass, and previously painted surfaces in good condition.
5-10 minutes between coats then 10 minutes before baking at 60°C
Yes , 10-15 minutes of short waves for the thickness of 150-250 µm. Do not exceed 60°C. Wait about 10 minutes before starting the heater drying.
Simple , pour the excess resin away into your solvent waste. This is rejection not separation. Do not mix it in as you will introduce air to the filler and increase your chances of pinholes
The primer should be mixed in a 4:1 ratio – four parts primer to one part hardener. This ensures optimal curing time, adhesion, and surface finish
When working with any 2K products, it is recommended to use personal protection equipment such as Air Fed respirator, safety goggles and gloves to Protect the eyes and respiratory system.
No, mixing technologies will only cause problems. always activate your paint using the information found on the Technical data sheet with the correct hardener stated on the same Technical data sheet.
The PPE needed to spray any 2K (2 pack) product including Epoxy is a good respirator, ideally air fed. safety glasses or goggles , gloves and overalls
Visual check: Look for a uniform matte finish. Touch Test. Surface should feel dry and firm, not tacky
Under standard conditions (20°C), the primer typically cures in 20–30 minutes before it can be sanded. Drying time may vary depending on ambient temperature, humidity, and film thickness
Visual check: Look for a uniform matte finish. Touch Test. Surface should feel dry and firm, not tacky
The primer should be mixed in a 5:1 ratio with the dedicated hardener. For example, 5 parts primer to 1 part hardener by volume. Always follow the manufacturer’s guidelines for best results
The primer can be applied using a spray gun with a nozzle size of 1.7–2.0 mm. Apply 2–3 coats, allowing appropriate flash-off time between layers. Ensure good ventilation and follow safety precautions during application.
Yes. The putty is formulated for exceptional ease of sanding, allowing for a smooth finish with minimal effort — even on large areas
This product uses advanced lightweight glass beads that reduce overall density, making it ideal for large surface repairs without adding unnecessary weight to the vehicle.
Firstly measure out 2% of the supplied hardener onto a mixing board, fold the hardener into the filler until a uniform colour is achieved. Try to to introduce air to the mix as this will cause pinholes
Simple , pour the excess resin away into your solvent waste. This is rejection not separation. Do not mix it in as you will introduce air to the filler and increase your chances of pinholes
This product uses advanced lightweight glass beads that reduce overall density, making it ideal for large surface repairs without adding unnecessary weight to the vehicle.
Yes, it can be applied to bare steel and aluminum, provided the surface is properly matted and degreased. For optimal adhesion and corrosion resistance, ensure thorough surface preparation.
Yes. The putty is formulated for exceptional ease of sanding, allowing for a smooth finish with minimal effort — even on large areas
Firstly measure out 2% of the supplied hardener onto a mixing board, fold the hardener into the filler until a uniform colour is achieved. Try to to introduce air to the mix as this will cause pinholes
The primer should be mixed in a 5:1 ratio with the dedicated hardener. For example, 5 parts primer to 1 part hardener by volume. Always follow the manufacturer’s guidelines for best results
Under standard conditions (20°C), the primer typically cures in 20–30 minutes before it can be sanded. Drying time may vary depending on ambient temperature, humidity, and film thickness
Yes, it can be applied to bare steel and aluminum, provided the surface is properly matted and degreased. For optimal adhesion and corrosion resistance, ensure thorough surface preparation.
The primer can be applied using a spray gun with a nozzle size of 1.7–2.0 mm. Apply 2–3 coats, allowing appropriate flash-off time between layers. Ensure good ventilation and follow safety precautions during application.
Yes , 10-15 minutes of short waves for the thickness of 150-250 µm. Do not exceed 60°C. Wait about 10 minutes before starting the heater drying.
The primer should be mixed in a 4:1 ratio – four parts primer to one part hardener. This ensures optimal curing time, adhesion, and surface finish
5-10 minutes between coats then 10 minutes before baking at 60°C
Yes, it adheres excellently to steel and aluminum, provided the surface is properly flatted and degreased. It also works well on zinc-coated steel, fiberglass, and previously painted surfaces in good condition.
When working with any 2K products, it is recommended to use personal protection equipment such as Air Fed respirator, safety goggles and gloves to Protect the eyes and respiratory system.
The primer should be mixed in a 4:1 ratio – four parts primer to one part hardener. This ensures optimal curing time, adhesion, and surface finish
5-10 minutes between coats then 10 minutes before baking at 60°C
Yes, it adheres excellently to steel and aluminum, provided the surface is properly flatted and degreased. It also works well on zinc-coated steel, fiberglass, and previously painted surfaces in good condition.
When working with any 2K products, it is recommended to use personal protection equipment such as Air Fed respirator, safety goggles and gloves to Protect the eyes and respiratory system.
The Indasa MTE Neon Masking Tape is the superior choice for automotive applications due to its exceptional adhesion, high-temperature resistance (up to 100ºC), UV protection, and waterproof performance. It’s specifically designed for demanding environments, ensuring clean, precise lines and reliable results, even in extreme conditions.
The PPE needed to spray any 2K (2 pack) product including Epoxy is a good respirator, ideally air fed. safety glasses or goggles , gloves and overalls
No, mixing technologies will only cause problems. always activate your paint using the information found on the Technical data sheet with the correct hardener stated on the same Technical data sheet.